Step 1 Adjust the collar
Proper Fit : The collar fit should be snug ,yet loose enough to allow one finger to fit between the strap and dog’ neck. Fit is important because a loose collar may cause inconsistent performance .It’s okay to trim any excess strap length.
Step 2 Power UP
Charge the collar Be sure to cover the charge jack with the gray plug when done .When the battery is low , the LED red light will flash continuously .After being charged ,the collar can work . Remember to use the charger we provide to charge. The collar with the fast charger , only need 2-3 hours to charge . The LED green light will flash while being charged. When the LED green light glow steadily , it indicates that the battery is full.
Don’t let the charger cover the charge jack over 24 hours. After being charged , please cut the charger from the charge jack .
Step 3 Using the Collar
The collar is activated when the unit is charged .Simply put the collar on your dog and enjoy the peace and quiet . A-108 Automatic No-Bark Collar Auto-Set feature will do all the work .
A-108 Automatic No-Bark Collar (Rechargeable)
Your Dog’s First Session
Monitor your dog during his first session .This is when he will learn what the collar means .Dogs learn at different speeds. It may take several barks or even several sessions for your dog to reduce his barking .Don’t worry –the Auto-Set feature starts at the lowest level and will adjust to the right level to motivate your dog to stop barking .The collar will remember the correct level between uses.
Resetting the Collar
The A-108 resets to lowest level each time it is charged .You may also reset the collar by recharging for as little as 1-minute .
Testing the Collar
You may wish to test the collar from time to time .To test the collar ,gently rub the metal probes against a hard non-glass surface .A solid red LED indicates that the unit is functioning properly .
Troubleshooting
If the collar appears not to be working ,try the following:
· Adjust the collar strap to fit
· Recharge the battery
· Check that the probes are touching the dog’s skin
· If necessary ,trim the dog’s hair or use the longer probes to ensure proper skin contact .
· If you cannot solve the problem by following these steps ,please call the service line to consult .
Components
· The A-108 has a waterproof collar that can be submerged in water during a dog’s normal activities ;do not place in a dishwasher .
· Two sets of probes are included so you can choose what’s right for your dog’s coat .
· The A-108 is powered by are chargeable Li-ion battery. When the battery is low and needs to be charged ,a red light will flash once every five seconds .The green light will glow steadily while being charged .
· This A-108 Bark Collar is designed to meet requirements set forth by United States country telecommunications authorities .Note that in some countries use may be limited due to national frequency planning requirements . The user is responsible for respecting those rules .
P3
The safe effective way to stop excessive barking
New Auto-Set feature automatically adapts to your dog’s bark .The more he bark ,the higher the correction. As he learns to bark less frequently ,the No –Bark Collar stops at the level just right for your dog .This exclusive patented technology delivers immediate ,effective stimulation for your dog ,and is fair to him by recognizing good behavior .
System Includes:
· Water-proof, microsized unit
· Rechargeable Li-ion batteries in collar
· Easy-to-adjust nylon buckle collar
· Short and Long probes for varying coat lengths
· Complete Operating Instructions
· Limit Lifetime Warranty
IMPORTANT ADIVCE
1、 Read the complete manual and follow all directions .If you have any questions ,please call the franchisers .
2、 This device is intended for use only on dogs .Never attempt to use it for any purpose not described in this manual .
3、 Never perform set-up procedures while the collar is on your dog .
4、 Any collar worn for extended periods can causes a condition similar to bedsores , known as Pressure Necrosis .To reduce the possibility ,you must do the following:
· Supervise your dog during the first 2 days of training
· Check the fit to prevent excessive pressure ;you should be able to insert one finger between the collar strap and your dog’ skin.
· Never leave the collar on the dog for more than 12 consecutive hours .
· Examine the dog’s neck daily for any signs of a rash or a sore .
· Wash the dog’s neck area and the probes of the collar weekly with a wash cloth and mild hand soap ;rinse thoroughly
If the condition persists beyond 24 hours ,see your veterinarian .
5、 Always use the rubber insulators between the collar strap and probes to provide insulation in damp conditions .
6、 Other collars and metal tags should be removed when using the No-bark collar as they may interfere with proper operation .
7、 Do not attempt to dismantle or repair any components of this system; doing so will void the warranty in full .The computerized circuitry should be serviced only by an authorized expert .
8、 Realize that because dogs have unique temperaments ,there is no way of knowing how your dog will react to the introduction of a No-bark collar system .For the safety of your dog , a long lead should be used during initial training so you have control of the situation.
9、 If you have reason to believe that your dog may pose a danger to others ,harm itself ,or react adversely to the collar ,do not rely solely on this product to train your dog . If your dog shows signs of growling ,snarling or biting while using the collar ,stop immediately .Aggression in dogs has many causes .We recommend that you consult a knowledgeable professional dog trainer or animal behaviorist who has experience with aggressive dogs if your dog has shown any of these characteristics.
10、 Occasionally ,a dog cannot be trained to respond to a No-bark collar .Sometimes even a properly trained dog may disobey a command .Therefore ,Invisible Technologies ,its distributors ,and dealers cannot guarantee that the system will in all cases keep the customer’s animal from disobeying commands.
|
