Multi-Functional 400M dog Trainer SH-9898 User Guide

Detailed Product Description

A: Press ON/OFF button on transmitter, then the power led in receiver will turn red, and working status led in receiver will turn blue, then receiver will be in working status.

Note: power switch in Transmitter can turn on/off receiver

B: Choose working mode by the press of MODE button.

 First press chooses REMOTE TRAINING mode, at the same time, its led will be flashing to indicate REMOTE TRAINING you had chosen;

Second press choose SELF-SUFFICIENT mode, at the same time, its led will be flashing to indicate SELF-SUFFICIENT you had chosen.

Similarly, next press choose REMOTE TRAINING, the next press choose SEL-SUFFICIENT

C: Choose stimulation method by the press of FUNCTION button

   First press chooses VIBRATION, the led on the right side of it will be flashing

   Second presses choose ULTRASONIC, the led on the right side of it will be flashing

   Third press chooses correction, the led on the right side of it will be flashing

   Forth press chooses VIBRATION & ULTRASONIC, the leds on the right side of them will be flashing

   Fifth press chooses VIBRATION & CORRECTION, the leds on the right side of them will be flashing

   Sixth presses chooses ULTRASONIC & CORRECTION, the leds on the right side of them will be flashing

   Seventh press chooses VIBRATION & ULTRASONIC & CORRECTION, the leds on the right side of them will be flashing

   Similarly eighth presses choose VIBRATION, ninth press choose ULTRASONIC----

D   Choose stimulation method degree

      After the choosing of working mode and stimulation method, Simply rolling the thumb knob, there can be ten intensity levels, then press Sound/Enter button two times, then the levels will be chosen. the age, weight, breed & your dogs nature should determine appropriate level of stimulation.

E: Stimulation confirmation

After choosing stimulation mode, stimulation method, and stimulation level, simply press sound/enter button, then the training method will be saved. Press any of function buttons (vibration, ultrasonic or correction), then the receiver will perform the training methods that saved successfully.

Important Note:

A); Transmitter acquiesces REMOTE as working mode, and VIBRATION as stimulation method, and acquiesces 3 degree as stimulation degree.

B)    One button realization function: simply pressing VIBRATION, ULTRASONIC or CORRECTION button will also make receiver perform those nearest saved working modes and stimulation methods successfully, and by pressing ENTER/SOUND button will emit BEEP--BEEP sound in receiver.

C)    Before realization of each stimulation (after transmitter transmits an instruction), the blue led will flash for 2 times indicate received the signal, then receiver will BEEP---BEEP, the desired function will be performed. So BEEP-BEEP sound can also adopt as a general warning for your dog.

D)   VIBRATION is the most humane stimulation method and then ULTRASONIC, these two functions are strongly recommended. CORRECTION is the most serious stimulation, please use it cautiously.  Correction actually is Shock.

E)    Stimulating intensity and stimulating time defined Stimulation degrees.

.

F)    Please do not open the receiver; otherwise whole machine will not be under warranty any longer.

G)   If receiver is going to out of power, the low power indicator will flash, on this condition, receiver cant perform any functions, recharge the battery immediately; and if the led in transmitter cant flash, please change the battery immediately.

H)    Transmitter adopts 9V alkaline battery, available in super markets or camera shops. Battery Lid is on the back of transmitter. Turn off the screws, take off the dead battery and replace it with new one.

I); Power supply in transmitter could affect valid remote range, and barriers also can affect remote range, what 450M valid range is a range under 9V power supply in a plain ground.

TEST

A)    VIBRATION: Vibration is quite obvious.

B)    ULTRASONIC: Human ear cannot hear Ultrasonic as it is a frequency above 20000HZ, but dog can feel it, it is a very effective sound in distracting a dog and stopping misbehaviours.

C)    CORRECTION: The test kit enclosed. Put the two wire ends around the metal poles, then under correction function, the led in the middle of the test kit will flash.

WARNING:

A)    Do not touch the correction metal poles, use test kit for test.

B)    The receiver is water proofed but its better not to put it into water and the same goes for the transmitter.