|
Remote Dog Training Collar User’s Manual
This is a product for dog training, which is consisted of a remote control and one to three dog collars. It could make voice in five levels of frequency and 50 grades of strong or weak electric shocks.
Install a 9V battery before use the product (Figure1); ensure proper polarity corresponding to battery terminal posts; two pieces of 4LR44 6V batteries coupling to collars, a stick on which printed polarity signs would be found when battery case of the collar is disclosed. ⊕indicates positive pole, while ⊖ indicates negative pole. Corresponding signs are also indicated on the included batteries. Install the battery properly referring to all the indications (Figure2).
Figure1
Figure2 Indicator light Discharge metal
This item could remote could control three collars at the same time. Therefore, make sure to match the three ID keys A, B and C with the remote controller respectively for the first use(details please refers to the instruction of ID matching). If you use one or two collars of them, please match any one or two of three keys respectively. If you use all the three collars, match all the three ID buttons with the three receivers one by one. For a better distinction, we made the collars in three different colors. Please use different color collars to distinguish.
When putting the collar on dog’s neck, adjust the length to make sure the discharging point to touch dog’s skin, but not too tight. Otherwise, the dog may feel uncomfortable. The collar would not generate shock if the discharging point can not touch the dog’s skin. Therefore, make sure the collar’s length is appropriate.
There are 5 sounds with different frequencies to use. When in use, you may use one of them to remind the dog to do something or warn its bad behavior. 01 has the highest frequency, it could make the dog feel uncomfortable; 05 has the lowest frequency, which could be used to remind the dog to do something. Higher frequencies could be used as a sound of warning while the static impulse could be used to punish its un-proper behaviors. 01 has the highest frequency, 02 lower and 05 the lowest. High frequency is not recommended from the beginning of use. Gradually switch the channel from the lowest frequency to higher. Stop when the dog feels obviously uncomfortably.
To match key A of remote control with ID collar, press key A on remote control first. According to your needs, press key X if you want to choose the sound function; press key~ if you want to choose the shock function. Adjust the vocal frequency or electric shock levels by pressing key ＋ or －. Then press key “SEND” to send orders, the receiver will receive the command from the remote controller and then will executive the command. In dark condition, press button “BL” to light the LCD. Make sure you press the right button and then press “send”, otherwise the dog may have unnecessary shocks.
When there is a long distance between the receiver and the controller, you may need to draw out the whole antenna on the controller. Then the receiver could receive the commands from the controller. The distance is limited though. It could reach 400 meters or even further in open areas. It could be only 250 metres in the steel reinforced concrete building. The battery installed in the product would be run out with more stand-by time and more times of use. When low power indication appears, the battery shall be replaced in time (refer to the low power instruction). The collar is designed water-proof. No need to take off the collar in rainy days. However, make sure to take off the collar when bathing the dog. Otherwise, the collar may be permanenly damaged if the water gets into the collar.
ID Verification: before initial use, the collar stays in test mode of manufacture. Press and key “M” and hold until LED lamp flashing. LED lamp flashed for three times then light off, which indicate exit of test mode. Press key “M” for one second, LED lamp maintains lighting, which indicates entrance of ID standby mode. initially installed battery, the remote control display status Ａ, press keyXto exit the status. Set A, Ｂ or C matching to ID standby mode of the collar, you only press key A, B or C, then press keyX, finally press key“SEND”, after the LED lamp flash three times, ID Verification has completed.(For example, when you set ID standby mode of collar matching to C: Press key C, then press key X, LED display: Ｃ X or any number key. At this time, press key“SEND”, after the LED lamp flashes three times, ID Verification has completed.)
Low Power Instruction:
There are three grids for power indication. When one grid is displayed for power indication, the battery shall be replaced. If the remote control was used continuously, the distance of remote control would be shortened gradually, even out of control.
Collars are ready for order signals as a receiver. Therefore, power consumption in small portion is natural and normal as if not having press key “SEND”. As time goes by, power of battery would be consumed completely. LED lamp keeping flash indicates the power of battery would be consumed completely; the battery shall be replaced in time. For saving power of battery, collars would enter sleeping mode when the dog stop moving or keep sleeping, and collars would not receive signals from the remote control.
The product is integrated with wireless transmission technology, it is not applicable by a person who supported by a heart pacemaker and the places that wireless phones are prohibited.
|
|
|
|
| Select Image |
 |
|
|
|
|
